Abstract
An inorganic binder is a good way to mitigate the environmental issues of organic binders containing phenol, formaldehyde, etc. One of the most representative materials in the field of inorganic moulding sand binders is a group of binder systems based on alkali silicate compounds, however, many aspects need to be..... More

Abstract
The effect of Al addition on the microstructure and mechanical properties of extruded Mg-Sn based alloy is investigated by adding 1 wt% Al to the Mg-7Sn-1Zn alloy and indirectly extruding the billets with and without the Al addition. The Al addition promotes dynamic recrystallization (DRX) behaviour during hot extrusion, which..... More

Abstract
Since strength and ductility have a trade-off relationship in Al alloys, controlling these properties using heat treatments requires careful attention to the dissolution and evolution of the reinforcing phases. In this study, the effects of solution and aging treatments on the microstructure and mechanical properties of Al-5.2Si-3.4Cu-0.28Mg alloy were investigated...... More

Abstract
Abstract: High-entropy alloys (HEAs), which are defined as a single phase crystalline solid solution with the composition of each constituent element in the range of 5-35 at%, have been the subject of intensive study in the last decade. Most of the HEA research is focused on alloy design, microstructural characterization,..... More

Abstract
In this paper, the soft magnetic properties and compaction density of Fe-Si-B-Nb-Cu nanocrystalline powder cores, mixed with two kinds of permalloy powders (Ni₇₀Fe₃₀ or Ni₅₀Fe₅₀), have been closely studied. Permalloy powders having an average diameter of 4μm were added in the range of 5 to 15 wt%, and the powder..... More

Abstract
Since their development in the 1970s ZrO₂ ceramics have been shown to be promising alternative materials for total hip arthroplasty (THA) and total knee arthroplasty (TKA). However, ZrO₂ is so brittle that in vivo failure can result from fracture of the ceramic femoral head and fracture of the ceramic acetabular..... More

Abstract
To realize focused design near-field conduction noise absorbers for sub-GHz frequencies, this study proposes screen-printed conductive grid films. The films’ advantages include large-scale production and easy control of electrical properties. A conductive grid film with a resistance value of approximately 70 Ω was screen printed on polyimide film substrate and..... More

Abstract
To study the effect of Al and Zr contents on the microstructural changes and tensile properties of Ni-Al-Bronze alloy, seven specimens were cast with different Al and Zr contents. The microstructure observation revealed that all specimens were composed of β’ and κ phases in a α matrix. With increasing Al..... More

Abstract
The square loop (SL) is the typical pattern of a frequency selective surface (FSS) with high inductance (L) and capacitance (C). In this study, modified patterns including split square loop FSS (SSL-FSS) and I-type FSS (I-FSS) are proposed, and their L and C values were estimated using the equivalent circuit..... More

Abstract
The influence of ultrasonic melt treatment (UST) combined with a change in cooling rates on the microstructure and elevated temperature mechanical properties of a hypereutectic Al-18Si-4Cu-3Ni piston alloy was investigated. Microstructural observation confirmed that UST effectively refined the sizes of primary Si and intermetallic compounds (e.g. ε-Al₃Ni) while promoting their..... More

Abstract
Feasibility studies are performed to determine the suitability of a novel simple synthesis technique for fabricating a new Ti alloy with improved strength and ductility, while exhibiting lower cell toxicity. Through consolidating pure Ti powders under a C atmosphere at elevated temperatures, a bulk form of the Ti alloy, in..... More

Abstract
In this study, a glass fiber is fabricated using a continuous spinning process from alkali resistant (AR) glass with 4 wt% zirconia. In order to confirm the melting properties of the marble glass, the raw material is placed into a Pt crucible and melted at 1650 ℃ for 2 h,..... More

Abstract
The effect of ultrasonic melt treatment (UST) on the microstructure and mechanical properties of Al-7Si-0.35Mg (A356) casting alloys was investigated. The particular aim of this study was to analyze the mechanism involved in the strengthening of the A356 alloys when fabricated by UST. The UST had little effect on the..... More

Abstract
The effects of particle size on the surface properties of HVOF spray coating were studied to improve of the durability of metal components. Micro and nano sized WC-12Co powders were coated on the surface of Inconel718, and the effects of particle size on surface properties were studied. Surface hardness was..... More

Abstract
Sn-doped ZnO (ZTO)/Ag/ZTO tri-layer films were deposited on glass substrates by radio frequency (RF) and direct current (DC) magnetron sputtering and then vacuum annealed at 100, 200 and 300 ℃ for 30 min with a proportions of H₂/N₂ gas flow of 6/6 sccm, to investigate the effects of annealing temperature..... More

Abstract
Despite of many attractive properties of TiN, the current concern about the TiN focuses on its low fracture toughness below the ductile-brittle transition temperature. To improve its mechanical properties, the approach generally utilized has been the addition of a second phase to form composites and to make nanostructured materials. In..... More

Abstract
Intermetallic compounds (IMCs) developed on the interface between a solder alloy and its bonding pads are an important factor in the failure of electronic circuits. In this study, the mechanical behaviors of the IMCs formed in the Cu-Ni-Sn ternary alloy system are investigated. Presumably, Ni can act as a diffusion..... More

Abstract
Despite of the many attractive properties of TiO₂, its low fracture toughness limits many industrial applications. To improve its fracture toughness, the approach commonly utilized has been the addition of a second phase, to form composites, and to make nanostructured composites. In this regard, highly dense nanostructured TiO₂ and TiO₂-graphene..... More

Abstract
The aim of this study is to establish an optimized hot-press sintering condition for aluminum matrix composites (AMCs) by analyzing their sintered microstructure and mechanical properties. The fabricated AMCs in this study consisted of a blend of commercial Ecka Alumix 431 powder, and Al-Si/SiC_p powder manufactured by gas atomizer (Al-Si/SiC_p)...... More

Abstract
Fe-(20, 45 wt%) Gd intermetallics were vacuum arc melted as the mother alloy of a neutron shielding and absorbing material. The structure of the cast Fe-20 wt% Gd intermetallics had primary dendrites with a short width of about 2 μm, which became coarse with increasing Gd content. The final compositions..... More

Material Analysis & Characterization

Abstract
ZnO buffer layers were deposited on mica substrates using a sol-gel spin coating method. Then, a thin film of metallic Zn was deposited onto the ZnO buffer layer/mica substrate using a thermal evaporator, and the deposited Zn thin films were then thermally oxidized in a furnace at 500 ℃ for..... More

Modeling and Simulation

Abstract
Yttrium Aluminum Garnet (YAG) single crystal has received much attention as the high power solid-state laser’s key component in industrial and medical applications. Various growth methods have been proposed, and currently the induction-heating Czochralski (IHCZ) growth method is mainly used to grow YAG single crystal. Due to the intrinsic properties..... More

Plastic Working & Materials Processing

Abstract
Laser surface carburizing can be achieved by a laser alloying mechanism, which includes melting the graphite coated substrate and dissolution of the graphite in the liquid state. The drawback of laser carburizing is that process-induced cracks frequently form on the carburized surface as a result of carbon enrichment and the..... More

Abstract
The aim of this study is to optimize the microstructure and mechanical properties of Ti-39Nb-6Zr (TNZ40) for bio-implant applications. TNZ40 was designed to have a low elastic modulus (~40 GPa) and good biocompatibility. However, the alloy shows relatively low strength compared to other titanium alloys for bio-implant. In the present..... More

Abstract
Open cell Cu foam, which has been widely utilized in various industries because of its high thermal conductivity, lightweight and large surface area, was successfully joined with Cu plate by diffusion bonding. To prevent excessive deformation of the Cu foam during bonding process, the bonding pressure should be lower than..... More

Abstract
The low mechanical properties of SiC limit its wide application despite many attractive properties. To improve the mechanical properties, a second phase has been generally added to make a nanostructured composite. In this respect, graphene was evaluated as the reinforcing agent of SiC. SiC-graphene composites were sintered within 2 min..... More

Abstract
CoTi and ZrO₂ nanopowders were mechanochemically synthesized from CoTiO₃ and Zr powders according to the reaction (2CoTiO₃ + 3Zr → 2CoTi + 3ZrO₂). The milled powders were then consolidated by pulsed current-activated sintering within two minutes under an applied pressure of 80MPa. The average hardness and fracture toughness of the..... More