Abstract
Because of their superior optical, and electrical properties, lead halide perovskites have emerged as potential materials for light-emitting-diodes. However, some obstacles have yet to be overcome for practical applications including low exciton binding energy, the difficulty of fabricating uniform perovskite films,, and their instability to heat, light, and moisture. In..... More

Abstract
In this study, we investigated the phase formation behavior of the FeSe₂-FeTe₂ system and the evolution of their thermoelectric transport properties. A series of Fe(Se_1-xTe_x)₂(x = 0, 0.2, 0.6, 0.8 and 1) compounds were synthesized by conventional solid-state reaction. Single phase orthorhombic structures were formed, except for FeSe_0.4Te_1.6(x = 0.2)...... More

Abstract
The effects of dissolution of the η′ phase by solution treatment on the mechanical properties of A7075-T6 alloy were investigated. Immediately after solution treatment of the T6 sheet at 450 ^oC or higher, elongation significantly increased and dissolution of the η′ phase occurred. η′ is the main hardening phase. After..... More

Abstract
We present a study on the synthesis of Bi₂Te_2.7Se_0.3 powders through an oxide reduction process and also on the effect of the oxide reduction process on the thermoelectric transport properties of the resulting Bi₂Te_2.7Se_0.3 compounds. Starting materials of Bi₂O₃, TeO₂ and SeO₂ were mechanical milled for homogeneous mixing, and then..... More

Abstract
Ni-Cr-Mo-V steel alloys for high-speed railway brake discs were prepared to investigate the effect of alloying element contents on the microstructure and mechanical properties. The Cr, Mo, Mn alloying elements were incorporated into the steel alloys, which contained low carbon content in the range 0.16 wt.% ~ 0.21 wt.% to..... More

Abstract
In this study, the liquation cracking susceptibility in the heat-affected zone of CM247LC superalloy gas turbine blades during repair welding was quantitatively evaluated using a newly developed pre-weld Varestraint test method. The repair welding geometry was replicated through Varestraint tests for the pre-weld bead. The liquation cracking susceptibility, that is,..... More

Abstract
The Ti-6Al-4V alloy has been widely used for structural materials due to high specific strength property, however it is difficult to cast because of high reactivity at high temperature. In this study casting characteristics and post-casting heat treatment were studied in the cast Ti alloy. The cast alloy was prepared..... More

Abstract
To manufacture composites with required properties, it is extremely important to select an appropriate filler. Carbon-based nano materials such as carbon black, graphene and carbon nanotube (CNT) have been extensively investigated as reinforcing and conducting fillers. Because of their high aspect ratio coupled with superior physical properties, 1-dimensional CNTs are..... More

Abstract
In order to investigate the mechanical properties of the developed wrought γ'-hardened Ni-based superalloy, LESS alloy (Low Eta Sigma Superalloy), and to understand the deformation behavior, tensile tests were carried out from room temperature to 800oC in comparison with IN 740H alloy. Like other superalloys, the tensile properties of the..... More

Abstract
Wearable strain sensors with high and broad sensitivity, high stretchability and excellent mechanical endurance will be widely useful in smart wearable electronics. In this work, we developed a stretchable strain sensor fabricated with a simple stencil printing technique. The stretchable strain sensor was fabricated using a multi-walled carbon nanotubes (MWCNTs)-Ecoflex..... More

Abstract
The demand for palladium (Pd) has increased and this has made it necessary to recover pure Pd from diverse secondary resources. To recover the small amount of Pd(II) present in spent electroplating solutions, Pd(II) is concentrated by cementation with zinc metal. In this work, a hydrometallurgical process consisting of leaching..... More

Abstract
Skinnerite Cu₃SbS₃, which consists of non-toxic and low-cost elements, is a potential thermoelectric material, however, studies on its thermoelectric properties are limited. In this study, the optimal conditions of mechanical alloying (MA) and hot pressing (HP) for the synthesis of the Cu₃SbS₃ phase were investigated, and its thermoelectric properties were..... More

Abstract
Nodular graphite cast iron is used in the railway and automobile industries because of its excellent workability, abrasion resistance, mechanical strength, and hardenability. To use nodular graphite cast iron in harsh environments, it is essential to examine their friction–wear properties in conjunction with the surface hardness of the materials. Therefore,..... More

Abstract
There is growing interest in the recovery of pure palladium (Pd) compound from cemented Pd from spent electroplating solutions due to increasing demand for Pd, and there is considerable motivation to develop an efficient recovery process. In conventional methods of leaching Pd metal, HCl solutions containing oxidizing agents are employed...... More

Abstract
The direct energy deposition (DED) method is an emerging manufacturing technique that has been recently highlighted due to its capabilities to coat materials with complex geometry for high temperature and highly corrosive environmental applications, such as steam turbine blade. Amongst metallic materials, SS304L has been reported to have superior corrosion..... More

Abstract
Two welding methods of FCAW (Flux-cored arc welding) + FCAW, and FCAW + GTAW (Gas tungsten arc welding) were compared to identify effective routes for STS 316L/A516-70N clad stainless steel. Since the welding speed of the FCAW + GTAW welding method is slower than that of the FCAW + FCAW..... More

Abstract
We investigated the effect of Ni doping on the electrical, thermal, and thermoelectric transport properties of FeSe₂ polycrystalline alloys. FeSe₂ alloys exhibit both n-type and p-type conduction at different temperatures and thus their practicality as a thermoelectric material is somewhat limited. In this study, Fe_1-xNi_xSe₂ polycrystalline samples with x =..... More

Abstract
A cold roll-bonding (CRB) process is applied to study the effects of stacking number on the microstructure and mechanical properties of roll-bonded and age-treated Al sheets. Commercial AA1050 and AA6061 sheets with a thickness of 2 mm were stacked alternately on each other to two and four layers, and roll-bonded..... More

Abstract
This study examined the effects of minor alloying elements (C, Ni, Cr, and Mo) on the long-term corrosion behaviors of ultrahigh-strength automotive steel sheets with a tensile strength of more than 1800 MPa. A range of experimental and analytical results showed that the addition of Ni, Cr, and Mo decreased..... More

Abstract
This study evaluated changes in delta-ferrite content depending on the preheating of AISI 316L stainless steel. We also determined the reasons for the variation in delta-ferrite content, which affects corrosion resistance. Changes in delta-ferrite content after preheating was confirmed using a Feritscope, and the microstructure was analyzed using optical microscopy..... More