Research Papers |
|
73 |
Effects of Two-Step Anodization on Surface Wettability in Surface Treatment of Aluminum Alloy 알루미늄 합금의 표면처리에 있어서 2단계 양극산화의 젖음성 영향
|
Abstract
Industrial anodizing of aluminum alloys is widely employed for various products, to improve corrosion and contamination protection as well as aesthetic appearance. At the same time, nanostructure fabrication using highly ordered porous aluminum oxides has been increasingly investigated in academic research for diverse micro-/nano applications. This approach is based on..... More
|
|
|
|
81 |
Effect of Post-Weld Heat Treatment on Microstructure and Hardness Evolution of Functionally Graded Materials Produced by Direct Energy Deposition 고에너지 직접 적층법으로 제조된 경사조성재료의 미세조직 및 경도 변화에 미치는 후열처리 영향 연구
|
Abstract
In this work, the effects of post weld heat treatment (PWHT) on the microstructure and mechanical properties of functionally gradient materials (FGM) was investigated. The FGM consisted of five different layers which were mixtures of austenitic stainless steel (type 316L) and ferritic steel (LAS). The ratio of type 316L and..... More
|
|
|
|
99 |
Optimization of Oil Adsorption Capacity by Aerogel Powder Synthesized Using Emulsion Droplets as Micro-reactors in Ambient Conditions from Sodium Silicate as Precursor
Abstract
In this study, silica aerogel particles were synthesized from emulsion droplets as micro-reactors at room temperature under ambient pressure. An economical precursor, sodium silicate, was used as the starting material for silica, and an emulsification technique was applied to form droplets in continuous phase. By controlling the composition of the..... More
|
|
|
|
113 |
Effect of Ultrasonic Cleaning of Titanium Turning Scraps Immersed in Alkaline Solution and Subsequent Preparation of Ferrotitanium Ingots
|
Abstract
Ti has excellent properties but is more expensive than other materials due to its high melting point, high reactivity and difficult processability. One way to lower the production cost of Ti products is to recycle Ti scraps. Before recycling Ti scraps, pretreatment to remove contamination is essential. Ti scraps can..... More
|
|
|
|
121 |
Fluorine-based Inductively Coupled Plasma Etching of α-Ga2O3 Epitaxy Film
|
Abstract
α-Ga2O3 has the largest bandgap (~5.3 eV) among the five polymorphs of Ga2O3 and is a promising candidate for high power electronic and optoelectronic devices. To fabricate various device structures, it is important to establish an effective dry etch process which can provide practical etch rate, smooth surface morphology and..... More
|
|
|
|
127 |
Calculated Electric Transport Properties of Thermoelectric Semiconductors Under Different Carrier Scattering Mechanisms 캐리어 산란 메커니즘에 따른 열전반도체의 이론 전자수송 특성 변화
|
Abstract
The widespread application of thermoelectric devices in cooling and waste heat recovery systems will be achieved when materials achieve high thermoelectric performance. However, improving thermoelectric performance is not straightforward because the Seebeck coefficient and electrical conductivity of the materials have opposite trends with varying carrier concentration. Here, we demonstrate that..... More
|
|
|
|
135 |
Nucleation and Growth-Controlled Morphology Evolution of Cu Nanostructures During High-Pressure Thermal Evaporation
|
Abstract
The formation of porous material structures has been widely investigated for the development of high-performance energy materials, catalysts, and chemical sensing devices. Various nanoporous structure fabrication methods are based on wet-chemical processes, which require precise control of the process parameters. Physical vapor deposition such as thermal evaporation utilizes high vacuum..... More
|
|
|
|
142 |
Fabricating Elastomeric Photomask with Nanosized-Metal Patterns for Near-Field Contact Printing
|
Abstract
When an elastomeric photomask is used for near-field contact printing, the high deformability of the elastomer mask plate enables gap-free full contact with the substrate, minimizing the effect of diffraction. This image-transfer technique provides sub-50 nm resolution and depth-of-focus-free lithographic capability with cost-efficient equipment. However, the method’s application is limited..... More
|
|
|
|